Airodump Ng For Windows

Airodump-ng -band bg ath0Here is an example screenshot:-CH 9 Elapsed: 1 min 2007-04-26 17:41 BAT: 2 hours 10mins WPA handshake: 00:14:6C:7E:40:80BSSID PWR RXQ Beacons #Data, #/s CH MB ENC CIPHER AUTH ESSID00:09:5B:1C:AA:1D 11 16 10 0 0 11 54. OPN 00:14:6C:7A:41:81 34 100 57 14 1 9 11 WEP WEP bigbear00:14:6C:7E:40:80 32 100 752 73 2 9 54 WPA TKIP PSK teddyBSSID STATION PWR Rate Lost Packets Probes00:14:6C:7A:41:81 00:0F:B5:32:31:31 51 11-11 2 14 bigbear(not associated) 00:14:A4:3F:8D:13 19 11-11 0 4 mossy00:14:6C:7A:41:81 00:0C:41:52:D1:D1 -1 11-2 0 5 bigbear00:14:6C:7E:40:80 00:0F:B5:FD:FB:C2 35 36-24 0 99 teddy-BSSIDMAC address of the access point. In the Client section, a BSSIDof '(not associated)' means that the client is not associatedwith any AP. In this unassociated state, it is searching for anAP to connect with.PWRSignal level reported by the card. Its signification depends onthe driver, but as the signal gets higher you get closer to theAP or the station. If the BSSID PWR is -1, then the driverdoesn’t support signal level reporting. If the PWR is -1for a limited number of stations then this is for a packet whichcame from the AP to the client but the client transmissions areout of range for your card.

1. Airodump Ng For Windows 12
2. Airodump Ng For Windows 6
3. Aircrack Ng Gui

Airodump Ng For Windows 12

Meaning you are hearing only 1/2 ofthe communication. If all clients have PWR as -1 then the driverdoesn’t support signal level reporting.RXQOnly shown when on a fixed channel. Receive Quality as measuredby the percentage of packets (management and data frames)successfully received over the last 10 seconds. It’smeasured over all management and data frames.

That’s theclue, this allows you to read more things out of this value. Letssay you got 100 percent RXQ and all 10 (or whatever the rate)beacons per second coming in. Now all of a sudden the RXQ dropsbelow 90, but you still capture all sent beacons. Thus you knowthat the AP is sending frames to a client but you can’thear the client nor the AP sending to the client (need to getcloser).

Airodump Ng For Windows 6

Another thing would be, that you got a 11MB card tomonitor and capture frames (say a prism2.5) and you have a verygood position to the AP. The AP is set to 54MBit and then againthe RXQ drops, so you know that there is at least one 54MBitclient connected to the AP.BeaconsNumber of beacons sent by the AP. Each access point sends aboutten beacons per second at the lowest rate (1M), so they canusually be picked up from very far.#DataNumber of captured data packets (if WEP, unique IV count),including data broadcast packets.#/sNumber of data packets per second measure over the last 10seconds.CHChannel number (taken from beacon packets). Note: sometimespackets from other channels are captured even if airodump-ng isnot hopping, because of radio interference.MBMaximum speed supported by the AP. If MB = 11, it’s802.11b, if MB = 22 it’s 802.11b+ and higher rates are802.11g. The dot (after 54 above) indicates short preamble issupported. ’e’ indicates that the network has QoS(802.11e) enabled.ENCEncryption algorithm in use.

OPN = no encryption,'WEP?' = WEP orhigher (not enough data to choose between WEP and WPA/WPA2), WEP(without the question mark) indicates static or dynamic WEP, andWPA or WPA2 if TKIP or CCMP or MGT is present.CIPHERThe cipher detected. One of CCMP, WRAP, TKIP, WEP, WEP40, orWEP104. Not mandatory, but TKIP is typically used with WPA andCCMP is typically used with WPA2. WEP40 is displayed when the keyindex is greater then 0.

The standard states that the index canbe 0-3 for 40bit and should be 0 for 104 bit.AUTHThe authentication protocol used. One of MGT (WPA/WPA2 using aseparate authentication server), SKA (shared key for WEP), PSK(pre-shared key for WPA/WPA2), or OPN (open for WEP).ESSIDThe so-called 'SSID', which can be empty if SSID hiding isactivated. In this case, airodump-ng will try to recover the SSIDfrom probe responses and association requests.STATIONMAC address of each associated station or stations searching foran AP to connect with. Clients not currently associated with anAP have a BSSID of '(not associated)'.RateThis is only displayed when using a single channel. The firstnumber is the last data rate from the AP (BSSID) to the Client(STATION).

The second number is the last data rate from Client(STATION) to the AP (BSSID).LostIt means lost packets coming from the client. To determine thenumber of packets lost, there is a sequence field on everynon-control frame, so you can subtract the second last sequencenumber from the la. Sudo airodump-ng mon0descriptionairodump-ngis used for packet capturing of raw 802.11 frames for theintent of using them with aircrack-ng. If you have a GPSreceiver connected to the computer, airodump-ng is capableof logging the coordinates of the found access points.Additionally, airodump-ng writes out a text file containingthe details of all access points and clients seen. Options-H,-helpShows the help screen.-i, -ivsIt only saves IVs (only usefulfor cracking). If this option is specified, you have to givea dump prefix (-write option)-g, -gpsdIndicate that airodump-ngshould try to use GPSd to get coordinates.-w, -writeIs the dump file prefix to use.If this option is not given, it will only show data on thescreen. Beside this file a CSV file with the same filenameas the capture will be created.-e, -beaconsIt will record all beacons intothe cap file.

By default it only records one beacon for eachnetwork.-u, -updateDelay secondsdelay between display updates (default: 1 second). Usefulfor slow CPU.-showackPrints ACK/CTS/RTS statistics.Helps in debugging and general injection optimization.

It isindication if you inject, inject too fast, reach the AP, theframes are valid encrypted frames. Allows to detect'hidden' stations, which are too far away tocapture high bitrate frames, as ACK frames are sent at1Mbps.-hHides known stations for -showack.-berlinTime before removing theAP/client from the screen when no more packets are received(Default: 120 seconds). See airodump-ng source for thehistory behind this option;).-c,., -channel,.Indicate the channel(s) tolisten to. By default airodump-ng hop on all 2.4GHzchannels.-b, -bandIndicate the band on whichairodump-ng should hop.

It can be a combination of’a’, ’b’ and ’g’ letters(’b’ and ’g’ uses 2.4GHz and’a’ uses 5GHz). Incompatible with -channeloption.-s, -cswitchDefines the way airodump-ngsets the channels when using more than one card. Validvalues: 0, 1 or 2.-r Reads packet from a file.-x Active Scanning Simulation(send probe requests and parse the probe responses).-output-formatDefine the formats to use(separated by a comma). Possible values are: pcap, ivs, csv,gps, kismet, netxml. The default values are: pcap, csv,kismet, kismet-newcore. ´pcap´ is for recordinga capture in pcap format, ’ivs’ is for ivsformat (it is a shortcut for -ivs).

Aircrack Ng Gui

’csv’ willcreate an airodump-ng CSV file, ’kismet’ willcreate a kismet csv file and ’kismet-newcore’will create the kismet netxml file. ’gps’ is ashortcut for -gps.Theses values can be combined with the exception of ivs andpcap.Filteroptions:-t, -encryptIt will only show networksmatching the given encryption. May be specified more thanonce: ’-t OPN -t WPA2’-d, -bssidIt will only show networks,matching the given bssid.-m, -netmaskIt will only show networks,matching the given bssid ^ netmask combination. Need-bssid (or -d) to be specified.-aIt will only show associated clients.interactionairodump-ng can receive and interpret key strokes whilerunning. The following list describes the currently assigned keysand supposed actions:aSelect active areas by cycling through these display options:AP+STA; AP+STA+ACK; AP only; STA onlydReset sorting to defaults (Power)iInvert sorting algorithmmMark the selected AP or cycle through different colors if theselected AP is already markedr(De-)Activate realtime sorting - applies sorting algorithmeverytime the display will be redrawnsChange column to sort by, which currently includes: First seen;BSSID; PWR level; Beacons; Data packets; Packet rate; Channel;Max.